Sharkstooth Stainless Steel Deck Fastenings Spike Clips Decking Fixing

Sharkstooth Stainless Steel Deck Fastenings Spike Clips Decking Fixing
Sharkstooth Stainless Steel Deck Fastenings Spike Clips Decking Fixing
Sharkstooth Stainless Steel Deck Fastenings Spike Clips Decking Fixing
Sharkstooth Stainless Steel Deck Fastenings Spike Clips Decking Fixing
Sharkstooth Stainless Steel Deck Fastenings Spike Clips Decking Fixing

Sharkstooth Stainless Steel Deck Fastenings Spike Clips Decking Fixing

Exclusively distributed in the UK by Round Wood. Corrosion resistant; manufactured in 304 Grade Stainless Steel. Fit your deck without unsightly face screws. Suitable for both softwoods and hardwoods. Model allows for 5mm spacing.

Top-up pack: 250 clips & accompanying nails, 15m2 coverage. Trade pack: 1000 clips & accompanying nails, 60m2 coverage. These are approximate coverage figures that assume 400m joist centres and 140mm wide boards. To calculate precise quantity requirements more precisely see coverage section below.

Display deck boards to their full potential. Maintain even spacing, (helps air-flow). No vertical fixing, so less moisture build up, (which can lead to rotting). Extremely secure, even when timber shrinks or expands.

Safer, as cannot pop out of surface. Fit first row of boards with a countersunk screw. Fill the hole with a timber plug.

Drive a fastener into exposed side of these decking boards. Nail fastener into joist using stainless steel nail supplied. Work your way along this first row of boards at chosen centres, securing Sharkstooth fasteners to the joist. Place second row of boards next to firmly fixed first row. Use a wooden block and heavy hammer to drive the boards onto exposed teeth. Work your way along the second row until it lies parallel to the first. Install the next row of Sharkstooth on the exposed edge of the second row, on the opposite side of the joist to the previous Sharkstooth. Work your way across each the deck repeating these steps. Fitting With Hardwoods For particularly dense hardwoods, such as Ipe, we recommend that a slot for the clip to is pre-routed with a 1.5mm slot cutter. This will make installation easier and prevent splitting. Set the router height so that a slot is cut at the point where the Sharkstooth will penetrate. Cut the slot to a depth of approximately 4mm, its base should be 10mm up from the base of the board. Length of slot should be approximately 30-40mm.

Joist centre: 400mm Board Width 90mm 31 units per m2. Joist centre: 450mm Board Width 90mm 28 units per m2. Joist centre: 500mm Board Width 90mm 25 units per m2. Joist centre: 550mm Board Width 90mm 23 units per m2. Joist centre: 600mm Board Width 90mm 21 units per m2.

Joist centre: 400mm Board Width 140mm 21 units per m2. Joist centre: 450mm Board Width 140mm 18 units per m2. Joist centre: 500mm Board Width 140mm 17 units per m2.

Joist centre: 550mm Board Width 140mm 15 units per m2. Joist centre: 600mm Board Width 140mm 14 units per m2. Use these figures to calculate your minimum requirements. Add two fasteners for each join then round up the total to the nearest 250.

Decking Fixings and Accessories Our range of garden decking accessories enables you to finish your deck to a very high standard. Our fixing products include stainless steel decking screws and plugs in a range of timbers, as well as the DeckWise Hidden Fastening system that we exclusively distribute in the UK. Uniquely, we also offer to pre-groove decking boards supplied by us for use with fastening clips to save you on-site fitting time. The item "Sharkstooth Stainless Steel Deck Fastenings Spike Clips Decking Fixing" is in sale since Thursday, March 5, 2020.

This item is in the category "Garden & Patio\Landscaping & Garden Materials\Paving & Decking\Decking Boards, Tiles & Joists". The seller is "round_wood_mayfield" and is located in Mayfield, East Sussex. This item can be shipped to United Kingdom.


Sharkstooth Stainless Steel Deck Fastenings Spike Clips Decking Fixing